2ef7 Map Thermostat Activation Lock
Have the codes checked! Do you know what codes are,What the light is for? The light is to warn the driver that there is a problem in the ABS system. Have the codes checked before replacing parts,the code will point you in the direction to go.This system can set numerous DTC'S DTC C1211 DTC C1214 DTC C1217 DTC C1218 DTC C1221-C1235 DTC C1236 DTC C1237 DTC C1238 DTC C1242 or C1243 DTC C1248 DTC C1251 (w/F45) DTC C1254 DTC C1255 or C1256 DTC C1261-C1274 DTC C1276, P1644, or P1689 DTC C1277 or P1571 DTC C1278 DTC C1281, C1283, or C1286 DTC C1282 DTC C1284 or C1285 DTC C1287 or C1288 DTC C1291 or C1293 DTC C1294 DTC C1295 Maybe your best bet would be to take your vehicle to a ASE certified repair shop or the dealer Jan 10, 2016 . Drk Typo3 Template Installieren Spiel.
2Ef7 bmw: photo: i have a 07 bmw. Map thermostat, activation - Open circuit Pulled this error out of DIS. 2EF5 DME: Map thermostat. 2013 2EF7 DME MAP. Sep 13, 2006 Bentley description, “Map Cooling Thermostat Control Circuit Electrical”. Peake description, “Electrical thermostat control final stage”.
Connect white (test lead) and black (ground lead) wires that are branched from harness approximately eight inches from ECM. After leads are grounded, the 'Check Engine' light will flash the diagnostic trouble codes. The DTC's are indicated by the flashing CEL. FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. Pinnacle Studio 14 Download Gratis Italiano Windows 7 on this page. After all DTC's have been displayed, the pattern will repeat.
I-MARK 84-85 Connect male and female test leads taped into wire harness near ECM. After leads are connected, the 'Check Engine' lamp will flash the trouble codes. The DTC's are indicated by the flashing CEL. FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23. If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.
86-87 Impulse located near the ECM connector, is used to actuate the Engine Control Module (ECM) trouble code memory within the module. Two terminals (A and C) of this connector are used to activate the diagnostic trouble code system in the ECM. With the ignition switch turned On, engine Off, connect a jumper wire between terminals A and C. The 'Check Engine' lamp will begin by flashing a DTC 12. DTC 12 = flash, pause, flash, flash. There will be a longer pause and a code 12 will repeat two more times.
This code indicates the self-diagnostic system is operating. The cycle will then repeat until the engine is started or the ignition is switched Off. In most cases, DTC's will be checked with the engine running since no DTC's other than DTC 12 or 51 will be present without the engine running. Remove jumper wire from ALDL connector before starting engine.
Reconnect jumper wire after engine is running. Throttle Body Fuel Injection The ECM test connection is located under the center console. A built-in, self diagnostic system will identify problems in the throttle body fuel injection system. When a problem is detected, the diagnostic system will illuminate the 'Check Engine' light. When the engine is started, the Check Engine light should turn off.
If the light remains lit, the self diagnostic has detected a problem. To determine where the problem exists, ground the 'Test' terminal of the connector with the ignition On, engine Off and watch the check engine light. Each DTC will flash three times (lowest to highest). Aug 21, 2014 .